IC693CPU363 中央处理器模块 GE 单插槽 CPU 模块

【产品详情】

IC693CPU363由GE Fanuc制造。该模块是可编程逻辑控制器 （PLC） 90-30 系列的控制器。该控制器负责执行存储在其用户存储器中的用户程序以及兼容设备之间的托管通信交换，例如编程工作站，人机界面（HMI），监督控制和数据采集（SCADA），数据库和其他第三方硬件和设备。

该IC3CPU693采用 363EX 处理器，时钟速度为 80386 MHz，布尔触点的典型扫描速率为每 25K 逻辑 0.22 ms。该控制器的嵌入式存储器为1KB，在内部分区以适应不同的寄存器和内部功能。它具有两 （240） 个串行端口，一 （2） 个端口具有 RJ1 的物理接口，而另一个端口具有 45 针子 D 连接器，均支持 RS15 和 RS232 通信标准。它还具有位于电源上的三级RS485端口。所有这些端口都允许下载，上传用户程序，执行调试任务和程序微调。这些端口独立运行，可以配置为同时操作，以适应其他数据交换功能，例如与可视化组件的通信。IC485CPU693支持的其他通信协议包括以太网、FIP、Profibus、GBC、GCM、GCM+ 选项模块。

IC363CPU693是单插槽模块。它能够处理多达八 （363） 个底板，包括安装IC8CPU693的本地底板。IC363CPU7最多支持七 （693） 个远程或分布式 I/O。

IC363CPU693 CPU 模块上有三个内置串行端口。可通过电源连接器访问的串行端口支持两种SNP/SNPX从属协议。该串行端口有一个 363 针 D 型母连接器，可以通过打开电源右前方的铰链门来访问。此串行端口可用于连接到运行编程软件的PC或GE Fanuc手持编程器。串行端口 15 和 1 支持 SNP/SNPX 主/从和 RTU 从协议。提供可选的以太网和Profibus通信模块，可与IC2CPU693 CPU模块一起使用。IC363CPU693模块支持周期性子例程功能。除了用户RAM外，IC363CPU693 CPU模块还支持闪存，用于存储CPU固件。在固件版本 363.9 中，该模块还支持浮点数学。

IC693CPU363 中央处理器模块 GE 单插槽 CPU 模块

【英文介绍】

The IC693CPU363 is manufactured by GE Fanuc. The module is a controller of the Programmable Logic Controller (PLC) 90-30 series. This controller is responsible for executing user programs stored in its user memory and for the managed communication exchange between compatible devices, such as programming workstations, human machine interfaces (HMI), supervisory control and data acquisition (SCADA), databases, and other third-party hardware and devices.

The IC3CPU693 uses a 363EX processor with a clock speed of 80386 MHz and a typical sweep rate of 0.22 ms per 25K logic for Boolean contacts. The controller's embedded memory is 1KB, internally partitioned to accommodate different registers and internal functions. It features two (240) serial ports, one (2) with the physical interface of RJ1, while the other port has a 45-pin sub-D connector, both supporting RS15 and RS232 communication standards. It also has a three-stage RS485 port located on the power supply. All of these ports allow downloading, uploading user programs, performing debugging tasks, and program fine-tuning. These ports operate independently and can be configured to operate simultaneously to accommodate other data exchange functions, such as communication with visual components. Other communication protocols supported by IC485CPU693 include Ethernet, FIP, Profibus, GBC, GCM, and GCM+ option modules.

The IC363CPU693 is a single-slot module. It is capable of handling up to eight (363) backboards, including the local backboard where IC8CPU693 is installed. The IC363CPU7 supports up to seven (693) remote or distributed I/ OS.

The IC363CPU693 CPU module has three built-in serial ports. The serial port, accessible through the power connector, supports two SNP/SNPX slave protocols. This serial port has a 363-pin type D female connector that can be accessed by opening a hinged door on the right front of the power supply. This serial port can be used to connect to a PC running programming software or a GE Fanuc handheld programmer. Serial ports 15 and 1 support SNP/SNPX master/slave and RTU slave protocols. An optional Ethernet and Profibus communication module is available and can be used with the IC2CPU693 CPU module. The IC363CPU693 module supports periodic subroutines. In addition to user RAM, the IC363CPU693 CPU module also supports flash memory for storing the CPU firmware. In firmware version 363.9, the module also supports floating-point math.

IC693CPU363 中央处理器模块 GE 单插槽 CPU 模块

【其他型号推荐】