IC660BBD110 独立的块I/O 具有16个输入点

【产品详情】

GE Fanuc IC660BBD110是一个独立的块I/O，具有16个输入点。该模块支持Genius总线通信协议，允许它安装在机器附近，而不需要沿模块安装底板、处理器或通信适配器。该模块是一个智能输入模块，支持菊花链拓扑结构，并直接向连接到同一网络的控制器或通信适配器报告。

IC660BBD110输入通道设计用于接收电压范围为93-132VAC，频率为47- 63hz，标称值为115VAC的信号。它具有25%至85%的可编程阈值，用于开和关状态。该模块还配备了内部通道诊断，能够检测断线和短路。这两种诊断特性还分别具有25% - 85%的可编程阈值和10-90%的固定阈值。该模块显示输入处理时间为1毫秒，软件可配置输入滤波器为10至100毫秒，增量为10毫秒。这种输入滤波器可以抑制噪声和信号反弹。

IC660BBD110模块尺寸为8.83英寸(22.44厘米)x 3.34英寸(8.48厘米)x 3.91英寸(9.93厘米)(HxWxD)，重4磅。(1.8公斤)。它带有LED指示灯，如单元OK, I/O启用和单独输入LED。从地到串行总线内部隔离1500V。

IC660BBD110通过安装在模块LED指示灯下方的端子排连接到天才总线。这个终端是一个3针终端，可以通过打开铰链门进入。本模块可安装在正向上或倒向下方向。

IC660BBD110分立输入块具有先进的诊断和可选的阈值。一些最常见的输入连接触点闭合连接，如开关、限位开关和按钮。它可以与2线接近开关输入和3线接近开关输入连接。

GE Fanuc Genius I-O IC660BBD110分立输入模块在32至140华氏度(0至60摄氏度)的温度范围内安全运行，并且可以安全存储在温度范围为-40至212华氏度(-40至100摄氏度)的环境中。IC660BBD110分立输入模块在运行和存储时的安全环境湿度要求在5% ~ 95%(无冷凝)之间。这个输入块重4磅或1.8公斤。它的尺寸为8.8 x 3.3 x 3.9英寸(22.4 x 8.4 x 9.9厘米)。对于设备保护，可以通过软件配置IC660BBD110离散输入块，以检测短路故障和断线故障。

IC660BBD110 独立的块I/O 具有16个输入点

【英文介绍】

The GE Fanuc IC660BBD110 is an independent block I/O with 16 input points. The module supports the Genius bus communication protocol, allowing it to be installed near the machine without the need to install a backboard, processor, or communication adapter along the module. The module is an intelligent input module that supports a Daisy chain topology and reports directly to controllers or communication adapters connected to the same network.

The IC660BBD110 input channel is designed to receive signals with a voltage range of 93-132VAC, a frequency of 47-63hz and a nominal value of 115VAC. It has a programmable threshold of 25% to 85% for on and off states. The module is also equipped with internal channel diagnostics, capable of detecting broken and short circuits. Both diagnostic features also have programmable thresholds of 25-85% and fixed thresholds of 10-90%, respectively. The module displays input processing times of 1 millisecond, and the software can configure input filters of 10 to 100 milliseconds in increments of 10 milliseconds. This input filter can suppress noise and signal bounce.

The IC660BBD110 module measures 8.83 inches (22.44 cm)x 3.34 inches (8.48 cm)x 3.91 inches (9.93 cm)(HxWxD) and weighs 4 pounds. (1.8 kg). It comes with LED indicators such as unit OK, I/O enabled and separate input LED. 1500V internal isolation from ground to serial bus.

The IC660BBD110 is connected to the Genius bus via a terminal block mounted below the module LED indicator. This terminal is a 3-pin terminal that can be accessed by opening the hinged door. This module can be mounted in a forward or backward direction.

The IC660BBD110 discrete input block features advanced diagnostics and selectable thresholds. Some of the most common input-contact close connections are switches, limit switches, and buttons. It can be connected to 2-wire proximity switch inputs and 3-wire proximity switch inputs.

GE Fanuc Genius I-O IC660BBD110 Discrete input modules operate safely in a temperature range of 32 to 140 degrees Fahrenheit (0 to 60 degrees Celsius) and can be safely stored in a temperature range of -40 to 212 degrees Fahrenheit (-40 to 100 degrees Celsius). The IC660BBD110 discrete input module ensures that the ambient humidity ranges from 5% to 95%(non-condensing) during operation and storage. This input block weighs 4 pounds or 1.8 kilograms. It measures 8.8 x 3.3 x 3.9 inches (22.4 x 8.4 x 9.9 cm). For device protection, the IC660BBD110 discrete input block can be configured through software to detect short circuit faults and disconnection faults.

IC660BBD110 独立的块I/O 具有16个输入点

【其他型号推荐】