IC660BBD021 I/O块模块 该模块由两2个组件组成
【产品详情】
IC660BBD021是一个I/O块模块,是Genius I/O块系列的一部分。该模块主要具有16个IO电路,每个电路可配置为输入、三态输入和离散输出通道。该模块由两(2)个组件组成,特别是目录号为IC660EBD021的电子组件和目录号为IC660TSD021的终端底座组件。该模块以前由GE发那科自动化公司生产,目前隶属于艾默生自动化公司。它被设计成一个独立的设备,作为分布式IO站,作为Genius I/O总线网络中的单个节点。它内置一个Genius Bus终端,用于连接到现有的Genius I/O网络,该网络也用于雏菊链连接到其他Block I/O或Genius功能设备。它还提供了一个端口来与手持终端(HHM)通信,允许本地监控。输入通道特性包括24vdc时0- 8vdc和48vdc时0- 16vdc的通状态电压,24vdc时17- 24vdc和48vdc时34- 48vdc的关状态电压。该模块的输入处理时间为1.7 ms,加上由所选输入滤波器引起的额外延迟。输出特性包括每个电路的最大稳态输出电流为2安培,在10毫秒持续时间内的最大涌流电流为10安培。当工作温度为35℃时,该I/O模块的总输出电流不超过15安培。输出电路的最大开关频率为每秒一次,延时时间为1ms。
GE IC660BBD021 I/O模块为16路I/O模块。它是一个接收I/O块,由24至48伏直流供电。该模块能够作为输入、三状态输入或输出模块工作。它与3线传感器完全兼容。这种I/O块变体不需要单独的电源模块。I/O块能够与三线固态传感器和机电传感器通信。该模块高度为8.83英寸,宽度为3.56英寸,深度为4.42英寸。它重约4磅。模块的前部有16个电路,带有单独的负载侧指示灯。当连接到特定的电路时,它们就会被照亮。IC660BBD021 I/O模块可以通过使用模块上部的监视器端口轻松连接到手持监视器。
GE IC660BBD021 I/O块属于开放式设备,应安装在保护框中。安装区域应保持清洁,无灰尘和污物。砌块采用对流冷却方法来维持其环境工作温度,并应始终有适当的气流。IC660BBD021 I/O块具有诊断和保护功能,包括电子短路保护,过载和过温检测,故障开关和空载检测。IC660BBD021 I/O块带有串行端口1和串行端口2以及屏蔽输入端口和屏蔽输出端口。两个LED指示灯称为I/O Enabled和Unit OK指示灯出现在块的前面。隔离块到块的额定电压为1500伏。电源脱落时间为10毫秒。
IC660BBD021 I/O块模块 该模块由两2个组件组成
【英文介绍】
The IC660BBD021 is an I/O block module that is part of the Genius I/O block family. The module mainly has 16 IO circuits, each circuit can be configured as input, three-state input and discrete output channels. The module consists of two (2) components, in particular an electronic component with catalog number IC660EBD021 and a terminal base assembly with catalog number IC660TSD021. The module was previously manufactured by GE Fanuc Automation and is now part of Emerson Automation. It is designed as a standalone device, as a distributed IO station, as a single node in the Genius I/O bus network. It has a built-in Genius Bus terminal for connecting to the existing Genius I/O network, which is also used for Daisy chain connections to other Block I/O or Genius enabled devices. It also provides a port to communicate with a handheld terminal (HHM), allowing for local monitoring. Input channel features include 0-8 VDC at 24vdc and 0-16 VDC at 48vdc, and 17-24 VDC at 24vdc and 34-48 VDC at 48vdc. The input processing time of the module is 1.7 ms, plus additional delays caused by the selected input filter. Output characteristics include a maximum steady-state output current of 2 amps per circuit and a maximum inrush current of 10 amps over a duration of 10 milliseconds. When the operating temperature is 35 ° C, the total output current of the I/O module does not exceed 15 amps. The maximum switching frequency of the output circuit is once per second, and the delay time is 1ms.
The GE IC660BBD021 I/O module is a 16-channel I/O module. It is a receiving I/O block powered by 24 to 48 volts DC. The module can work as an input, three-state input, or output module. It is fully compatible with 3-wire sensors. This I/O block variant does not require a separate power module. The I/O block can communicate with three-wire solid-state sensors and electromechanical sensors. The module is 8.83 inches tall, 3.56 inches wide, and 4.42 inches deep. It weighs about four pounds. The front of the module has 16 circuits with separate load side indicators. When connected to a specific circuit, they are illuminated. The IC660BBD021 I/O module can be easily connected to a handheld monitor by using the monitor port on the upper part of the module.
The GE IC660BBD021 I/O block is an open device and should be installed in the protection enclosure. The installation area should be kept clean and free of dust and dirt. The block adopts a convection cooling method to maintain its ambient operating temperature and should always have appropriate airflow. The IC660BBD021 I/O block has diagnostic and protective functions, including electronic short-circuit protection, overload and overtemperature detection, fault switching and no-load detection. The IC660BBD021 I/O block has serial ports 1 and 2 as well as shielded input ports and shielded output ports. Two LED indicators called the I/O Enabled and Unit OK indicators appear on the front of the block. The isolation block to block voltage is rated at 1500 volts. Power off time is 10 milliseconds.
IC660BBD021 I/O块模块 该模块由两2个组件组成
【其他型号推荐】
AUTOLIV | Sim.Mod. B0760 627913600B | HIMA | H4135A | TERASAKI | ERC-244 |
KONGSBERG | RMP201-8 | LAM | 810-370141-001 | ABB | HIEE200038R0001 |
ABB | CMA130 3DDE300410 | ABB | 5SHY3545L0010 | FOXBORO | FBM214B P0927AH |
WOODWARD | 8200- 1302 | FOXBORO | FBMSVH | HONEYWELL | 05701-A-0302 |
AUTOLIV | GTW.MOD. B0110 627697900B | ABB | DI01 | WOODWARD | 9907-1290 |
BENTLY | 60M100-00 | SIEMENS | 3RK2200-0CE02-0AA2 | DANFOSE | EKC 361 |
MOTOROLA | MVME6100 | Pepperl+Fuchs | HID2030SK | ABB | MB510 3BSE002540R1 |
ICS TRIPLEX | T8111C | Bently | 3500/42M | ABB | DAPI100 3AST000929R109 |
WATL OW | CLS216-10000000 | ABB | AI04 | ABB | CI522A 3BSE018283R1 |
ABB | PFEA111-653BSE050091R65 | ABB | GOP2 | SCANLAB | INTELLISCANDE III14-532NM SCANLAB |
ABB | PFEA111-653BSE050090R65 | FOXBORO | FBMSVH | BENTLY | 3500/22M 138607-02 |
ENTERASYS | A4H124-24TX P0973JM | YASKAWA | CLSR-33-N2CE-1 | ABB | UFC762AE101 3BHE006412R0101 |
ENTERASYS | A4H124-24FX P0973JN | SAIA | PCD3.E165 | ABB | XVC767AE105 3BHB007209R0105 |
ENTERASYS | A4H254 -8F8T P0973JP | SAIA | PCD3.W610 | ABB | XVC768115 3BHB007211R115 |
ENTERASYS | C2G170-24 P0973BL | SAIA | PCD3.W340 | ABB | 5SHY5055L0002 3BHE019719R0101 GVC736BE101 |
ENTERASYS | A2H254-16 P0973BK | 菲尼克斯 | PSR-SPP-24UC/URM4/5X1/2X2/B | HONEYWELL | FC-PSU-UNI2450U V2.1 |