IC660BBD020 是一个16通道源组合离散I/O模块

【产品详情】

IC660BBD020是艾默生自动化PLC组件。IC660BBD020以前由GE发那科制造，是一个天才块I/O，具体来说，是一个16通道源组合离散I/O模块。该模块具有离散输入和离散输出的功能，可以独立配置输入或输出。它具有与三线固态和机电传感器的额外兼容性。这个I/O块带有22个连接端子，可容纳电源连接，现场信号布线和天才总线连接。

IC660BBD020接受24 VDC或48 VDC标称电压输入电平的输入信号，并支持源布线配置。此外，它可以产生相同的电压输出水平。该模块还具有输出脉冲测试兼容性。输出电源默认上电，输出最后状态保持。它还提供了软件可配置的滤波器时间，选择范围为10毫秒至100毫秒。它具有内部诊断功能，如电子短路保护，过温保护，故障开关检测，三态输入的开线检测，过载检测和关机以及空载检测。该模块的输入响应时间为1.7 msec，加上配置的输入滤波器时间，范围为5至100mS，输出响应时间为1.0 msec。

通过嵌入式Genius通信接口交换I/O。这个接口允许菊花链连接到任何类型的另一个Genius I/O块，或者直接连接到驻留在Genius总线上的主控制器。终端电阻必须跨第一个和最后一个节点的串行1和串行2端子连接，以关闭天才总线环路。

IC660BBD020汇聚I/O模块是GE发那科设计的3线制传感器兼容器件。该模块运行16个电路，额定电压为24 / 48伏直流。该模块与GE系列90-30 PLC系统兼容。它可以通过控制器或手持监控设备轻松编程和监控。它也可以连接到运行Windows操作系统的个人电脑上。模块负载的额定电流为2安培。IC660BBD020 I/O模块具有强大的诊断系统，可以监测短路、过温、过载、空载和故障开关情况。该模块可用作输入、输出或三态输入设备。模块的输入滤波时间可以在10到100毫秒之间选择。先进的块诊断系统，可以轻松排除安装和操作过程中的问题和错误。

GE IC660BBD020 I/O块的输入处理时间为1.7毫秒，带有滤波器延迟。输入阻抗为5.6千欧姆，电压为24至48伏，输入阻抗为1.8千欧姆，电压为24伏。输入输出模块采用开放式结构，仅供室内使用。最高环境温度不应超过60摄氏度，并有适当的气流穿过砌块。应将IC660BBD020 I/O块放置在远离EMC噪声和发热设备的地方。该模块可以很容易地安装在水平和垂直位置。为了保证地面的完整性，使用了星形垫圈。I/O块是向后兼容的，它也可以与旧的现有PLC系统一起使用。

IC660BBD020 是一个16通道源组合离散I/O模块

【英文介绍】

The IC660BBD020 is a Emerson Automation PLC component.  Formerly manufactured by GE Fanuc, the IC660BBD020 is a Genius Block I/O, specifically, a 16-channel Source combination discrete I/O module.  This module has the capabilities of a Discrete input and Discrete output, being able to be configured an input or output independently.  It has an added compatibility of being used with 3-wire solid-state and electromechanical sensors.  This I/O block comes with 22 connection terminals, accommodating power connection, fields signal wiring and Genius Bus connectivity.

The IC660BBD020 accepts input signals with nominal voltage input levels of 24 VDC or 48 VDC and supports source wiring configuration.  Additionally, it can generate the same voltage output levels.  It also module comes with output pulse test compatibility.  Output power up default and output last state hold.  It is also provided with software configurable filter time with selection range of 10 ms to 100 ms.  It comes with internal diagnostic capabilities such as Electronic short circuit protection, Overtemperature protection, Failed switch detection, Open wire detection for tristate inputs, Overload detection and shutdown and No-load detection.  This module has input response time of Input 1.7 msec plus the configured input filter time with range of 5 to 100mS while the output response time is 1.0 msec.

The exchanges I/O through the embedded Genius communication interface.  This interface allows daisy chaining to another Genius I/O block of any type or being connected directly to the master controller residing on the Genius Bus.  Terminating resistors must be connected across serial 1 and serial 2 terminals of the first and last node to close the Genius bus loop.

The IC660BBD020 sink I/O block is a 3-wire sensor compatible device designed by GE Fanuc.  The block runs with 16 circuits and it has a voltage rating of 24 / 48 Volts DC.  This module is compatible with the GE Series 90-30 PLC systems.  It can be programmed and monitored easily with a controller or handheld monitoring device.  It can also be connected to a personal computer running the Windows operating system.  The current rating for the load of the module is 2 Amps.  The IC660BBD020 I/O block has a powerful diagnostics system and it can monitor short circuits, over-temperature, overload, no-load, and failed switch situations.  The module can be used to work as an input, output, or a tristate input device.  The input filter time can be selected for the module between 10 and 100 milliseconds.  The advanced diagnostics system of the block can easily troubleshoot issues and errors during the installation and operation.

The GE IC660BBD020 I/O block has an input processing time of 1.7 milliseconds with a filter delay.  The input impedance of the block is 5.6 kiloohms for 24 to 48 Volts of voltage and 1.8 kiloohms for 24 Volts of voltageThe I/O block is built with open architecture and it is made for indoor use only.  The maximum environmental temperature should not exceed 60 degrees Celsius with proper airflow across the block.  The IC660BBD020 I/O block should be kept away from EMC noise and heat-generating devices.  The module can be mounted easily in both horizontal and vertical positions.  To provide ground integrity, star washers are used.  The I/O block is backwards-compatible and it can also be used with older pre-existing PLC systems.

IC660BBD020 是一个16通道源组合离散I/O模块

【其他型号推荐】