IC660BBA106 电流源模拟输入块 具有单独隔离通道的输入点

【产品详情】

IC660BBA106是一个天才I/O块，是一个电流源模拟输入块。这个I/O块具有六(6)个具有单独隔离通道的输入点。该模块接受0-20 mA和4-20 mA输入信号，用于连接各种设备，如变送器，变频驱动器(VFD)，阻尼器，面板仪表，数据记录仪，信号隔离器，转换器和其他设备。

IC660BBA106 Block I/O通过提供115VAC或125VDC的外部电压供电，标称值和实际工作范围为93-132VAC或105-145 VDC。它的分辨率为1 (1)μ a，用户可选择的更新速率为16.6mS至400mS。它的通道-通道隔离额定有效值为1500V。它有一个内置的内部诊断，如范围不足，范围过广，高报警，低报警，和开线。

IC660BBA106需要在0°C至+60°C(+32°至+140°F)的温度范围内工作，存储温度为-40°至+100°C(-40°至+212°F)，湿度为5%至95%，无冷凝，工作振动为5-10 Hz 0.2“(5.08mm)位移，10- 200hz 1G。

IC660BBA106的开路电压为24VDC，短路电流< 75ma，回路阻抗最大为1000欧姆(0mA至20mA)，最大为800欧姆(20mA至25mA)，在50,60hz时正常模式抑制-45dB。

IC660BBA106内置状态LED指示灯，如Unit OK和I/O enabled。正常工作时，两个LED指示灯应保持常亮状态。其他LED特征可以描述强制，禁用和非通信块I/O模块。

IC660BBA106 I/O模块设计了故障报告功能，可以自动诊断系统，检查输入流、报警和其他事件中的超量程和量程情况。

GE IC660BBA106 I/O模块正常使用时最大散热12瓦。正常工作温度要求为0 ~ 60℃。每个单独的电路块有2个报警。一个告警用于低值，另一个用于高值。该块具有电路缩放、CPU冗余和输入转换时间。通道到通道隔离的均方根值为1500伏，块的热漂移为每摄氏度70 ppm。I/O块的输入阻抗为100欧姆。IC660BBA106 I/O模块在50至60赫兹的频率下具有-45 dB的正常模式抑制。块的输入精度为满读数的0.1%。

IC660BBA106 电流源模拟输入块 具有单独隔离通道的输入点

【英文介绍】

The IC660BBA106 is a genius I/O block that is a current source analog input block. This I/O block has six (6) input points with separate isolated channels. The module accepts 0-20 mA and 4-20 mA input signals and is used to connect various devices such as transmitters, variable frequency drivers (VFDS), dampers, panel meters, data loggers, signal isolators, converters and others.

The IC660BBA106 Block I/O is powered by providing an external voltage of 115VAC or 125VDC with a nominal and actual operating range of 93-132VAC or 105-145 VDC. It has a resolution of 1 (1) μa and user selectable update rates from 16.6mS to 400mS. Its channel-to-channel isolation rating is 1500V RMS. It has a built-in internal diagnostics such as under-range, over-range, high alarm, low alarm, and open line.

The IC660BBA106 needs to operate in a temperature range of 0°C to +60°C(+32° to +140°F), storage temperature of -40° to +100°C(-40° to +212°F), humidity of 5% to 95%, no condensation, operating vibration of 5-10 Hz 0.2 "(5.08mm) displacement, 10-200hz 1G.

The IC660BBA106 has an open circuit voltage of 24VDC, a short circuit current of < 75ma, a loop impedance of up to 1000 ohms (0mA to 20mA), a maximum of 800 ohms (20mA to 25mA), and a normal mode suppression of -45dB at 50,60hz.

The IC660BBA106 has built-in status LED indicators such as Unit OK and I/O enabled. In normal operation, the two LED indicators should be kept on. Other LED features can describe mandatory, disabled, and non-communication block I/O modules.

The IC660BBA106 I/O module is designed with a fault reporting function to automatically diagnose the system and check for overrange and range conditions in input streams, alarms and other events.

The maximum heat dissipation of the GE IC660BBA106 I/O module is 12 watts. The normal operating temperature ranges from 0 to 60 ° C. Each individual circuit block has 2 alarms. One alarm is used for low values and the other for high values. The block has circuit scaling, CPU redundancy, and input conversion time. The root-mean-square value of channel-to-channel isolation is 1500 volts and the thermal drift of the block is 70 ppm per degree Celsius. The input impedance of the I/O block is 100 ohms. The IC660BBA106 I/O module has normal mode rejection of -45 dB at frequencies of 50 to 60 Hz. The input accuracy of the block is 0.1% of the full reading.

IC660BBA106 电流源模拟输入块 具有单独隔离通道的输入点

【其他型号推荐】