IC660BBA105 是一个模拟输出模块 具有6个模拟输入通道

【产品详情】

IC660BBA105是一个天才I/O块组件。该模块是一个模拟输出模块，在115 VAC或125 VDC的输入电源电压下工作。该模块是一个面板安装设备，通过提供的安装孔固定，使用8-32尺寸的螺钉固定，并使用星形垫圈连接到地面。它可以安装到任何外壳，提供足够的空气流动和保护工业污染物。

IC660BBA105主要具有6个模拟输入通道，可提供4- 20ma信号。每个通道具有可配置的输出保持功能，这是一项重要的安全相关功能，允许模块在处理器错误或操作模式改变的情况下保持当前输出值。此外，单个电路缩放到工程值可以设置，以提供一个可用的读数。它还能够感知超距和过距情况以及输出反馈误差。本模块输出通道无需校准即可投入使用。

IC660BBA105的输出分辨率为6µA，输出更新频率为25 ms，满量程读数的精度为0.15%。它在0-24 mA的输出范围内工作，每摄氏度典型的热漂移为35 PPM。

终端现场信号线的推荐线径为awg# 14(横截面平均为2.1mm2)，最小推荐线径为awg# 20(横截面平均为0.54 mm2)。对于串行总线布线，单线连接的推荐线尺寸为awg# 12线(平均3.3mm2横截面)和awg# 14线(每条平均2.1mm2横截面)。当一个端子需要2根导线时。串行总线的最小推荐线尺寸为awg# 22(横截面平均为36mm2)。

IC660BBA105模块是兼容GE发那科90-30系列PLC系统的Genius I-O模块。该模块共有32个端子和6个输出块。该模块的分辨率为6微安。它带有6个点，模块的工作电压为93至132伏交流电压和105至145伏直流电压。io模块的输出范围为4 ~ 20毫安或0 ~ 24毫安。这个天才I-O模拟设备有一个开放的外壳，它应该防止水溅和空气传播的污染物。IC660BBA105模块高8.83英寸，宽3.50英寸，深3.94英寸。模块的正面配备了一个单元OK LED和一个I/O Enabled LED。

IC660BBA105模块具有1500伏的块对块隔离，隔离时间为1分钟。正常工作时，io模块产生12w的热量作为散热。模块所在环境温度不超过60摄氏度。IC660BBA105模块通过监控接口连接手持编程器。I/O模块的工作频率为50 ~ 60赫兹。它配备了串行1，串行2，屏蔽输入和屏蔽输出连接端口。I/O块具有独立的电路，这些电路在电气上是通用的，但与其他电路隔离。IC660BBA105模块在I/O块中具有增强的诊断功能之一，可以轻松检测空载错误、过载错误、短路错误和其他错误。波特率为76.8波特率和38.4波特率。

IC660BBA105 是一个模拟输出模块 具有6个模拟输入通道

【英文介绍】

The IC660BBA105 is a Genius I/O Block component. This module is specifically an analog output module that operates at an input supply voltage of 115 VAC or 125 VDC. This module is a panel mounted device, secured through the provided mounting holes, fastened using 8-32 size screws and connected to ground using star washers. It can be installed to any enclosure, providing adequate air flow and protection to industrial contaminants.

The IC660BBA105 mainly features Six (6) analog input channels that delivers 4-20 mA signals. Each channel has configurable output hold feature which is an important safety related functionality, allowing the module to hold the current output value in the event of processor error or change in operating mode. Additionally, individual circuit scaling to engineering values can be set to provide a usable readout. It is also capable of sensing overrange and underrange situations as well output feedback error. Output channels of this module do not require calibration to be put into operation.

The IC660BBA105 has output resolution of 6µA with output update frequeny of 25 ms and accuracy of 0.15% of full-scale reading. It operates at output range of 0-24 mA and thermal drift of 35 PPM per degree C typical.

Recommended wire size for terminating field signal wires are AWG #14 (avg 2.1mm2 in cross-section) with minimum recommended size of AWG #20 (avg .54mm2 in cross-section). For serial bus wiring, recommended wire size is AWG #12 wire (avg 3.3mm2 cross-section) for single wire connection and AWG #14 wires (each avg 2.1mm2 in cross-section). When 2 wires are needed in a single terminal. Minimum recommended wire size for serial bus is AWG #22 (avg .36mm2 in cross-section).

The IC660BBA105 module is a Genius I-O module that is compatible with the Series 90-30 PLC system by GE Fanuc. The module has a total of 32 terminals and 6 output blocks. The resolution of the module is 6 microAmps. It comes with 6 points and the operating voltage of the module is 93 to 132 Volts AC and 105 to 145 Volts DC. The output range of the I/O module is 4 to 20 milliAmps or 0 to 24 milliAmps. This Genius I-O analog device has an open enclosure and it should be protected against water splashes and air-borne contaminants. The IC660BBA105 module is 8.83 inches in height, 3.50 inches in width, and 3.94 inches in depth. The front of the module is equipped with a Unit OK LED and an I/O Enabled LED.

The IC660BBA105 module has a block to block isolation of 1500 Volts for a time period of 1 minute. For regular operation, the I/O module generates 12 Watts of heat as energy dissipation. The temperature of the module’s environment should not exceed 60 degrees Celsius. The IC660BBA105 module uses the monitoring port to connect with a handheld programming unit. The operating frequency of the I/O module is 50 to 60 Hertz. It is equipped with Serial 1, Serial 2, Shield In, and Shield Out connection ports. The I/O block has independent circuits that are electrically common but that are isolated from other circuits. The IC660BBA105 module features one of the enhanced diagnostic features in an I/O block that can easily detect no-load errors, overload errors, short-circuit errors, and other errors. The module has a baud rate of 76.8 and 38.4 kbaud.

IC660BBA105 是一个模拟输出模块 具有6个模拟输入通道

【其他型号推荐】