BENTLY 3500/20 125744-02 工业控制模块

BENTLY  3500/20 125744-02  工业控制模块

BENTLY  3500/20 125744-02  工业控制模块

BENTLY 3500/20 125744-02 DVI连接器有24个引脚，最多可容纳两个TMDS链路和VESA DDC和EDID服务。DVI规范定义了两种类型的连接器DVI Digital（DVI-D）仅支持数字显示（用于VMIVME-7807/VME-7807RC）

DVI集成（DVI-I）支持数字显示并向后兼容带模拟显示器（不支持）VMIVME-7807/VME-7807RC使用带有单个TMDS链路的DVI-I连接器。DVI-I接口可容纳12针或24针DVI插头连接器或新型连接器一种模拟插头连接器，使用四个附加引脚，加上一个接地平面插头保持模拟RGB信号的恒定阻抗。VMIVME-7807/VME-7807RC能够同时驱动两台监视器使用Intel 855GME GMCH的时间。图形控制器允许使用一个连接到VMIACC-0590/ACC-0590RC或VMIACC-0586的数字监视器/ACC-0586RC RTM，从后I/O P2接头引出。第二个是标准连接到VMIVME-7807/VME-7807RC前面板的SVGA监视器，使用标准DB15连接器。、

3500监视器与多个

认证选项（-02）通过2区认证

标准（包括ATEX和北美

区域）。区域2标准规定增加

较高电压下的间距要求，以及

3500/33继电器不符合这些间距

要求。因此，3500/33继电器

使用多重批准选项订购

历史上仅限于较低

电压高于其他订购的电压

批准选项。使用更高的电压会

违反危险区域证书

与多个批准选项关联。

（北美Division 2标准

与仅CSA批准选项相关

（-01）不需要相同的间距，因此

证书未被增加的

电压在以下方面是可以接受的

使用电压的危险区域要求

仅CSA认证时，高达300 Vdc

已订购选项（-01）。）

2.如果3500/33是功能安全的一部分

（SIL）系统，功能安全证书

需要限制电压。更高的电压

不允许用于功能安全（SIL）

系统。

3.可以将现场接线连接到

3500/33继电器

暴露于潜在的人类接触。这可能

在高电压下存在电击危险。

希望使用3500/33继电器的客户

在高达300 Vdc的电压下

建议硬件功能完善

处理这个电压，但那是适当的

应采取安全预防措施

关于电击危险。

BENTLY  3500/20 125744-02  工业控制模块

The BENTLY 3500/20 125744-02 DVI connector has 24 pins and can accommodate up to two TMDS links and VESA DDC and EDID services. The DVI specification defines two types of connectors DVI Digital (DVI-D) supports only digital display (for VMIVME-7807/VME-7807RC)

DVI Integration (DVI-I) supports digital display and is backward compatible with analog display (not supported) The VMIVME-7807/VME-7807RC uses a DVI-I connector with a single TMDS link. The DVI-I interface can accommodate 12-pin or 24-pin DVI plug connectors or a new type of connector an analog plug connector that uses four additional pins, plus a ground plane plug to maintain a constant impedance of the analog RGB signal. The VMIVME-7807/VME-7807RC can simultaneously drive two monitors to use Intel 855GME GMCH. The graphics controller allows the use of a digital monitor /ACC-0586RC RTM connected to the VMIAC-0590 /ACC-0590RC or VMIAC-0586, leading from the rear I/O P2 connector. The second is an SVGA monitor that is standard connected to the VMIVME-7807/VME-7807RC front panel, using a standard DB15 connector. ,

3500 monitors with multiple

Certification Options (-02) Pass Zone 2 certification

Standards (including ATEX and North America

Area). Area 2 standard provisions added

Higher voltage spacing requirements as well

The 3500/33 relay does not conform to these spacing

Ask. So, 3500/33 relays

Order with the multiple approval option

Historically limited to lower

The voltage is higher than the other ordered voltages

Approve the option. Using a higher voltage would

Violation of hazardous area certificate

Associated with multiple approval options.

North American Division 2 standard

Related to the CSA approval option only

(-01) does not require the same spacing, therefore

The certificate has not been added

The voltage is acceptable in the following respects

Hazardous area requirements for use voltage

Up to 300 Vdc when CSA certified only

Ordered options (-01).

2. If 3500/33 is part of functional safety

(SIL) System, Functional Safety Certificate

Need to limit voltage. Higher voltage

Not allowed for functional safety (SIL)

System.

3. You can connect onsite cables to

3500/33 relay

Exposure to potential human contact. This may

Danger of electric shock at high voltage.

Customers who wish to use 3500/33 relays

At voltages up to 300 Vdc

It is recommended that the hardware function is complete

Deal with this voltage, but that's appropriate

Safety precautions should be taken

About the shock hazard.

BENTLY  3500/20 125744-02  工业控制模块